Cart 0

2005 - 2007 Accord Hybrid Installation Instructions

We Need Your Accord Hybrid!

Do you live in Northern California?

We need a car to photograph and complete our
step-by-step installation instructions.

We are happy to compensate you for your time.
Please email us if you can help.

These instructions are very basic.

We are hoping to get a vehicle to develop proper instructions. We apologize for the limited instructions at this time.

Email us for any help needed, we are happy to assist.

Begin by opening the trunk and removing the right side trunk liner. This will allow you to access the IPU cooling fan assembly, which can be seen here.

You may need to unscrew a trunk cargo hook as well as remove multiple clips to gain access to the IPU fan.

Unplug the main wire harness from the IPU cooling fan.
CAR HARNESS VERSION CHECK:

Inspect your Car Harness and compare it to the photo at left.

If you have the newer style harness, like the example on the right side of the photo, proceed to the next step.

If you have the older integrated fan harness (like the example on the left side of the photo), CLICK HERE to jump past the fan wiring installation.

Begin the cooling fan wire harness installation by cutting the fan wire harness approx 1.5 inches (40mm) from the fan side male plug (female pins) as shown.

Remove and discard black wire tubing.

Click on diagram
at right for
larger image

Strip 1/8 inch (3.2mm) of insulation off of each wire.

Carefully install each wire into the hybrid battery cooling fan control sub-assembly using the wire diagram shown above.

Be sure connections are tight! Try pulling the wires out, they should be firmly in place!

This is what it should look like when both connections are made.

Carefully install hybrid battery cooling fan control sub-assembly enclosure lid using four provided screws.

NOTE LID ORIENTATION, it is not symmetrical. There are alignment tabs at one end to ensure proper installation.

(No image)
Note: Should you ever need/want to reverse the installation of the Car Harness, we are happy to provide a blank connection terminal for a nominal fee.  Contact us for more information.

Install the Car Harness/cooling fan wire assembly onto the fan.

Once the charger car harness is connected to the fan, it should look like this. 

Note the location of the HV+ and HV- (red & black) wires. This is where you will route them foreword to the IPU compartment after removing the rear seat back.

The rear seat bed is removed by pulling two black tabs at both front ends and then removing a screw on the driver side of the cushion, between the backrest and the seat bead gap.

Photo credit: Abhishek Mitra

Remove the three 10mm seat back screws and then pull straight up on the rear seat to remove it.

Photo credit: Abhishek Mitra

Unscrew the eight Torx T30 bolts holding IMA cover on.

Note the final screw (shown in the red square) cannot be removed until the IMA battery breaker is switched off.

Photo credit: Abhishek Mitra

Route the red and black wires through from the trunk area as shown.

Photo credit: Michael Ruge

Once the IPU compartment cover has been removed, route the red and black wires through from the trunk area as shown.

Connect the red HV+ and black HV- wires as shown.

Route the charger wire as shown. Secure using the provided zip ties.

 

(Civic Hybrid shown for reference)

IMPORTANT - Test the charger before re-assembling the vehicle. Always connect the charger to the car harness before plugging it into the wall and unplug it from the wall before disconnecting it from the car.

To perform the initial function test: First, make sure all fingers and tools are clear of all wiring and IMA battery components. Plug the charger into the car harness. With the IMA battery circuit breaker still turned off, plug the charger into the wall. After a few seconds, it should read approx 180 volts on the meter and both the charger and IPU fans should be running. Next, move the IMA battery circuit breaker to the on position. You should see the voltage drop as the charger voltage equalizes with the voltage level of the battery pack. This should happen quickly. The voltage level should be stable and not fluctuating. Both fans should still be running. If anything is wrong, stop and contact us. If the fan is ‘pulsing’ (powering on and off) every few seconds, stop and contact us.

This completes the test. Unplug the charger from the wall, turn the IMA battery circuit breaker off, and disconnect the charger from the car harness.

(No image)
SAFETY WARNING!

Other than the short installation tests, do not run the grid charger with the IPU compartment open or only partially installed. The cover MUST be installed with all bolts properly tightened and the IMA breaker cover installed in order for the IMA battery to be properly cooled while charging.

If you run the charger with the IPU cover off for any length of time, you WILL cook your battery!

(No image)
Reassemble the vehicle in reverse order of dis-assembly.
(No image)
Click here for the Prolong Battery Charger User Guide.

Return Home